How to check tyre pressure: A simple guide for cars and vans
Learn how to check tyre pressure correctly, where to find the recommended PSI and how often you should check your tyres to stay safe on the road.
Published: | Author: Van Monster
Whether you drive a car, van or pickup, keeping your tyres at the correct pressure is one of the easiest ways to improve safety, fuel efficiency and tyre lifespan. Incorrect tyre pressure can affect everything from braking performance to running costs. Both underinflated and overinflated tyres can create problems on the road.
The good news? A tyre pressure check only takes a few minutes.
Safety and vehicle handling
Tyres are the only point of contact between your vehicle and the road. If tyre pressures are too low or too high, this can affect:
- Braking distance.
- Steering response.
- Road grip, especially in wet conditions.
- Vehicle stability when cornering.
- Overall driving comfort.
Underinflated tyres can also generate excess heat, increasing the risk of tyre damage or failure.
Fuel economy and tyre wear
Maintaining the correct tyre pressure can help:
- Improve fuel efficiency.
- Reduce rolling resistance.
- Extend tyre life.
- Prevent uneven tyre wear.
- Lower vehicle running costs.
Even slightly underinflated tyres can increase fuel consumption over time, making regular checks worthwhile.
Finding the correct tyre pressure
Before carrying out a car or van tyre pressure check, you’ll need to know the vehicle manufacturer’s recommended pressure.
You can usually find this information:
- Inside the driver’s door frame.
- Inside the fuel filler flap.
- In the vehicle owner’s manual.
- On a tyre pressure information sticker.
Tyre pressures are usually shown in:
- PSI, meaning pounds per square inch.
- BAR, another unit used to measure air pressure.
The correct pressure may differ between:
- Front and rear tyres.
- Lightly loaded and fully loaded vehicles.
Important: Always follow the vehicle manufacturer’s recommendation rather than the maximum PSI printed on the tyre sidewall.
Checking and adjusting your tyre pressure
Follow these simple steps to check and adjust your tyre pressure correctly.
Step 1: Check the tyres when cold
Tyres heat up during driving, which causes air pressure to increase temporarily.
For the most accurate reading:
- Check the tyres before driving.
- Alternatively, wait at least three hours after driving.
Step 2: Remove the valve cap
Unscrew the valve cap from the tyre and keep it somewhere safe.
Step 3: Attach a tyre pressure gauge
Place the gauge firmly onto the valve stem. You may hear a brief hiss of air when attaching the gauge. This is normal.
The gauge will then display the current tyre pressure.
Step 4: Compare the reading
Compare the reading with the vehicle manufacturer’s recommended PSI.
Recommended pressure: 36 PSI
Current reading: 31 PSI
The tyre requires additional air.
Step 5: Inflate or release air as needed
If the tyre pressure is too low:
- Use an air compressor at a petrol station or garage.
- Add air in short bursts.
- Recheck the pressure after each adjustment.
If the tyre pressure is too high:
- Press the centre pin inside the valve to release a small amount of air.
- Recheck the pressure after each adjustment.
Step 6: Repeat the process for every tyre
Remember to check:
- The front tyres.
- The rear tyres.
- The spare wheel, if fitted.
The spare tyre is often forgotten but may be needed in an emergency.
Step 7: Refit the valve caps
Once the checks are complete, replace all valve caps securely to help keep dirt and moisture away from the valves.
Where can I do a tyre pressure check?
You can check tyre pressure using:
- A handheld tyre pressure gauge.
- A digital tyre inflator.
- Petrol station air pumps.
- Facilities at garages and tyre centres.
Many fuel stations and fast-fit garages provide tyre inflation facilities, either free of charge or for a small fee.
How often should you check tyre pressure?
As a practical rule, check your tyre pressures:
- At least once a month.
- Before long journeys.
- Before carrying heavy loads.
- Before towing a trailer.
- During significant temperature changes.
Colder weather can reduce tyre pressure, so carrying out additional checks during winter is a good idea.
Signs your tyres may need attention
You may need to check your tyre pressure sooner if you notice:
- A tyre pressure warning light.
- Uneven tyre wear.
- Reduced fuel economy.
- The vehicle pulling to one side.
- Heavier steering than normal.
- Tyres visibly looking low.
If any of these symptoms appear, carry out a tyre pressure check as soon as it is safe to do so.
Frequently asked questions
How do you check tyre pressure by hand?
It’s difficult to check tyre pressure accurately by hand alone.
Although an underinflated tyre may feel softer when pressed, the only reliable way to measure tyre pressure is with a tyre pressure gauge or digital inflator. These provide an exact PSI reading and help ensure your tyres are set correctly.
How do you find out tyre pressure by registration number?
Some online vehicle information tools allow you to enter your registration number to find the manufacturer-recommended tyre pressures.
You can also check:
- Inside the driver’s door frame, typically on a sticker.
- Inside the fuel filler flap.
- In the owner’s manual.
Always verify the details against the information supplied by the vehicle manufacturer.
Where can I get my tyre pressure checked?
Many petrol stations, tyre centres and garages provide tyre pressure checking or inflation facilities.
You may also find air pumps at:
- Supermarket fuel stations.
- National tyre fitting chains.
- Vehicle service centres.
Availability and charges vary, so it’s worth checking locally if you’re looking for a free tyre pressure check near you.
Is 40 PSI too high for car tyres?
Not necessarily. Some vehicles require pressures close to or above 40 PSI, particularly larger vans, SUVs and vehicles carrying heavy loads.
However, if the manufacturer recommends 32 PSI and the tyres are inflated to 40 PSI, the tyres may be overinflated. Always follow the pressure specified by the vehicle manufacturer rather than relying on a generic PSI figure.
